Direct answer: Choose a vibratory screen grader for free-flowing granules, seeds and whole spices that need several size fractions. Choose a rotary drum grader for rounder or larger pieces that blind flat screens. Choose a roller grader when you must size by diameter or thickness without dropping fragile product. Confirm the choice with a sieve test of your own material.
Key takeaways
- Grading separates by size. Sorting separates by quality such as colour, defects or density. Many lines need both.
- Particle shape matters as much as particle size. Round, flat and elongated pieces behave differently on the same screen.
- Most grading problems come from near-size particles, blinded screens and uneven feed, not from the motor or frame.
- A simple fraction balance from a lab sieve test tells you how big each outlet, bin and conveyor must be.
What does a grading machine actually do in a food line?
A grading machine splits one feed stream into two or more size bands. Each band then goes to its own use, price or downstream process. In a spice line, for example, oversize may go back to a crusher while fines go to a powder blend.
Grading is different from sorting. A sorting machine rejects discoloured, damaged or foreign pieces. A grading machine classifies good product by size so that drying, roasting, frying and packing behave evenly.
How do vibratory, rotary and roller graders differ?
The three common designs use different motions and opening shapes. That changes which dimension of the particle they really measure.
Vibratory screen graders
A vibratory grader moves product across one or more flat screen decks. Particles smaller than the aperture fall through. Stacking decks gives several fractions from one machine.
This design suits free-flowing granular material: whole spices, seeds, grains, sugar-like granules and dried vegetable pieces. Weak points are blinding (particles stuck in openings) and smearing of oily or sticky material.
Rotary drum graders
A rotary grader is a slowly turning perforated cylinder. Product tumbles along the drum and meets sections with larger openings in turn. The tumbling keeps openings clearer than a flat deck for round pieces.
It suits larger, roundish items such as nuts, pellets or whole bulbs. It is usually less precise for long or flat pieces, which can slide through end-first.
Roller graders
A roller grader uses pairs of rollers whose gap widens along the machine. Each piece drops when the gap matches its smallest cross-section. The motion is gentle, so it suits fruit, vegetables, nuts and other fragile pieces.
Roller graders are not a good fit for small granules or powders. For powders, a gyratory sifter is the usual classifier.
| Feature | Vibratory screen | Rotary drum | Roller |
|---|---|---|---|
| Best product form | Free-flowing granules, seeds, whole spices | Larger, round or pelletised pieces | Fruit, vegetables, nuts, fragile pieces |
| Dimension it mostly sorts by | Width (intermediate dimension) on square openings; thickness on slots | Width, with some end-on passing of long pieces | Smallest cross-section (diameter or thickness) |
| Number of fractions | Several, by stacking decks | Several, by drum sections | Several, along roller length |
| Main risk | Blinding, smearing of oily product | Lower precision for flat or long pieces | Not suited to small granules |
| Product handling | Moderate | Tumbling, can abrade soft items | Gentle |
Why does particle shape change the grading result?
Short answer: A screen opening tests whether a particle can pass in its best orientation. A long, thin piece can pass end-first through a square opening that a round piece of the same length cannot. So two products with the same “size” can grade very differently.
Use these rules when you write your specification:
- Square or round openings mainly sort by width. Use them for roundish granules.
- Slotted openings mainly sort by thickness. Use them for flakes, slices and flat seeds.
- Roller gaps sort by the smallest cross-section. Use them when diameter or thickness sets the grade.
State in your purchase specification which dimension defines the grade. “Size 4–6 mm” alone is not enough.
What causes poor grading accuracy, and how do you check it?
Short answer: Poor accuracy usually comes from overloading the screen, blinded openings, uneven feed across the width, or too many near-size particles. Check accuracy by sieving samples from each outlet in a laboratory and counting how much material sits in the wrong band.
| Symptom | Likely cause | First check |
|---|---|---|
| Fines found in the oversize outlet | Bed too deep; product leaves the deck before it can pass | Reduce feed rate; check feed spread across full width |
| Capacity falls during the shift | Blinding of openings | Inspect cleaning balls, brushes or tappers; check product moisture |
| Long pieces in the small grade | End-on passing | Try slotted openings or a roller grader |
| Broken pieces and dust | Too much drop height or aggressive motion | Reduce drop heights and stroke; review grader type |
Use certified test sieves for these checks so that results are comparable from day to day. ISO 3310-1 sets technical requirements for woven-wire test sieves.
How do you size outlets and conveyors from a sieve test?
A fraction balance turns a laboratory sieve result into equipment sizes. The example below uses illustrative assumptions, not data from any plant.
Assumptions: feed rate 2,000 kg/h; lab sieve test shows 70% in the target band, 20% oversize and 10% undersize (all by mass, as received).
- Target grade: 2,000 × 0.70 = 1,400 kg/h
- Oversize: 2,000 × 0.20 = 400 kg/h (to re-crush or to a separate grade)
- Undersize: 2,000 × 0.10 = 200 kg/h (to powder, blend or by-product)
If oversize is crushed and returned to the grader, the grader feed rises. With all 400 kg/h returned, the grader must handle up to 2,400 kg/h at steady state, depending on how much of the crushed material falls back into the target band. Size the grader and return conveyor for that loop, not just for fresh feed.
Real fractions change with crop, season and upstream drying. Repeat the sieve test on several lots before you fix capacities.
Where does the grader sit in a complete line?
Position depends on what the grade controls:
- Before drying or roasting: even piece size gives even moisture and colour. This matters in spice processing lines and in chips lines fed by a chips cutter.
- After drying: grading separates saleable sizes and fines for powder.
- After grinding: a sifter classifies powder to a mesh specification.
For coconut products, the particle grades of desiccated coconut are a good worked case. See this group guide on specifying desiccated coconut grades and sizing the grading line. For fresh produce intake, our earlier article on fruit and vegetable sorting, grading and washing covers washing and inspection in more depth.
Non-food bulk materials such as fertilisers and minerals often use heavier enclosed screens. GTI Group’s engineering division describes its gyratory vibrating screening machines for those duties.
What should you check before buying a grading machine?
GTI’s grading machine page lists vibratory, rotary and roller-based designs, multi-stage grading, and SS304, SS316 or mild steel construction, with capacities customised by project. Use the checklist below to get a design that fits your product.
- Product name, form and shape (round, flat, elongated, flakes).
- Required grades, and which dimension defines each grade.
- Lab sieve analysis of at least three representative lots.
- Feed rate in kg/h and hours per day.
- Product moisture (state wet basis) and oil or sugar content.
- Fragility: is breakage or dust a quality defect?
- Hygiene needs: food-contact material, cleaning access, dust control.
- What happens to each off-grade stream.
- Space, height and connection to upstream and downstream machines.
Frequently asked questions
Can one machine both grade and sort?
Some lines combine both functions in one frame, but they solve different problems. Size grading does not remove discoloured pieces of the right size. Plan a separate sorting step when visual defects matter.
How many decks do I need?
Number of decks equals number of cut points. Three grades need two cut points, so two screen decks. Add a scalping deck on top if large foreign matter is common.
Is stainless steel always required?
Food-contact parts should be made from materials suitable for food contact and easy cleaning, as general food hygiene principles require. Non-contact frames may use other materials if they can be kept clean.
Talk to GTI about your project
Planning a grading or sorting stage for spices, grains, nuts or chips? Contact Genex Tech Industries LLP (GTI Group) to discuss your material, production capacity, product specifications and utility requirements. To help us respond usefully, please share your product or raw material, required capacity, feed and final moisture (state wet or dry basis), finished-product specification, available utilities, installation location and project timeline.
Email: mktg@foodtechprojects.com
Call or WhatsApp: +91-93300-77417 | +91-87774-75596 (WhatsApp)
Website: https://foodtechprojects.com/
For Industrial Dryers: https://gtidryers.com
This article gives general technical guidance. Figures marked as illustrative are examples, not plant guarantees. Equipment selection and performance for your material should be confirmed through trials and engineering assessment.
References
- ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth. International Organization for Standardization. www.iso.org
- Codex Alimentarius, General Principles of Food Hygiene (CXC 1-1969). FAO/WHO. www.fao.org
