Direct answer: Use a filter press when the liquid carries a lot of solids and you want a firm cake. Use a sparkler filter to polish liquids that are already fairly clear. Use a centrifugal filter when solids must be removed continuously or the cake must be spun dry. Many edible oil lines use two stages: bulk removal, then polishing.

Key takeaways

  • Solids load, particle size and how you want to handle the cake decide the choice more than flow rate alone.
  • A filter press handles heavy solids loads. A sparkler filter polishes. A centrifugal filter separates by force and can run with frequent discharge.
  • Two-stage filtration is common for expeller oil, juices and extracts.
  • Test your own liquid before you size anything. Filtration rates vary widely between products.

How does each type of filter work?

Filter press

A filter press pumps the liquid into chambers formed between filter plates covered with filter cloth. Liquid passes through the cloth. Solids stay behind and build a cake. When the chambers are full, the press is opened and the cake is discharged.

GTI’s filter press page lists filtration areas from 5 to 1,000 m², operating pressure up to 16 bar, cake thickness of 20–50 mm, and MS, SS304, SS316 or PP construction, all customisable. Listed uses include edible oils, starch, beverages, coconut processing and effluent treatment.

Sparkler filter

A sparkler filter is a closed vessel holding a stack of horizontal plates. Each plate carries filter sheets or pads. Liquid flows through the sheets and leaves fine particles behind. It holds less cake than a filter press, so it suits final polishing.

GTI’s sparkler filter page lists filtration areas of 1–20 m², 5–50 plates, operating pressure up to 6 kg/cm², flow rates of 500–20,000 LPH, and SS304 or SS316 construction. Listed uses include edible oil polishing, herbal extracts, essential oils and beverages.

Centrifugal filter

A centrifugal filter spins the liquid in a basket. The spinning creates a force many times stronger than gravity. Liquid passes through the basket lining while solids are held back and spun drier.

GTI’s centrifugal filter page lists capacities of 100–5,000 kg/h, basket diameters of 300–1,500 mm, speeds of 1,000–3,000 RPM, and manual or automatic discharge. Listed uses include fruit pulp, starch, dairy, edible oils and botanical extraction.

Which filter suits which job?

Factor Filter press Sparkler filter Centrifugal filter
Best solids load High Low (polishing) Medium to high
Separation principle Pressure through cloth; cake builds Pressure through sheets or pads Centrifugal force through basket lining
Cake handling Firm cake, opened and discharged Small cake on plates, cleaned at intervals Spun cake, manual or automatic discharge
Enclosure Open when discharging Closed vessel Closed basket during running
Typical role in oil lines Main clarification after expeller Final polishing before storage or packing Separating heavy solids or spinning cakes

How strong is the force in a centrifugal filter? A worked example

Short answer: The force depends on basket radius and speed. Doubling speed multiplies the force by four. Even mid-range machines generate forces around a thousand times gravity.

Illustrative example: basket diameter 500 mm (radius 0.25 m), speed 2,000 RPM.

  • Angular speed ω = 2π × 2,000 ÷ 60 ≈ 209.4 rad/s
  • Acceleration = ω² × r = 209.4² × 0.25 ≈ 10,960 m/s²
  • Relative to gravity (9.81 m/s²): about 1,120 g

Higher force speeds up separation but also raises stress on the basket and needs good balance. Speed is therefore set by the machine design, not chosen freely on site.

What does edible oil need from filtration?

Short answer: Expeller oil carries fine meal particles called foots. These must be removed to give clear oil that stores well. The Codex standard for named vegetable oils sets a maximum of 0.05% m/m insoluble impurities as a quality characteristic.

A common sequence is:

  1. Settling or screening to remove coarse foots.
  2. Filter press for the main clarification. Foots cake can often be returned to the expeller feed.
  3. Sparkler filter for polishing before storage tanks and filling and packing.

GTI’s oil expeller page lists filter press and sparkler filter units as part of complete oil lines. For coconut oil, the virgin coconut oil machinery page on our coconut division’s site shows filtration within a VCO line.

Why does temperature change filtration speed?

Filtration rate falls as liquid viscosity rises. Most oils and syrups get thinner when warm, so they filter faster. Too much heat, however, can harm oil quality or flavour. Set temperature as a compromise and confirm it in trials.

Filter aids can also help with slimy or very fine solids. They build a porous layer that keeps the cloth or sheet from blinding. Use only food-grade aids that are acceptable in your target market.

What goes wrong, and how do you fix it?

Problem Likely cause Corrective action
Cloudy filtrate Torn cloth or sheet; poor sealing Inspect media and gaskets; recirculate first runnings
Pressure rises fast Media blinding; very fine solids Pre-coat or filter aid; settle first; check temperature
Wet, sloppy press cake Cycle stopped early; low pressure Fill chambers fully; check pump and pressure
Vibration in centrifuge Uneven cake; worn parts Even loading; balance and maintenance checks

Where else are these filters used?

How do you run a useful filtration trial?

Short answer: Filter a representative sample of your real liquid at the planned temperature and record how flow and pressure change over time. That gives data a supplier can scale, instead of guesses from flow rate alone.

  • Take samples from the actual process point, not from a storage tank where solids have settled.
  • Measure solids content and note how fast solids settle in a jar.
  • Record filtrate volume against time and the pressure used.
  • Check filtrate clarity, and measure insoluble impurities if a standard applies.
  • Repeat with and without a filter aid if fine solids blind the media.

What data do you need to size a filter?

  • Liquid type, temperature and approximate viscosity.
  • Flow rate and operating hours.
  • Solids content and particle size, from a lab test if possible.
  • Required clarity or specification.
  • What happens to the cake.
  • Material of construction needs (food grade, corrosion).

Frequently asked questions

Can a sparkler filter replace a filter press?

Only when solids are low. With high solids, a sparkler filter fills quickly and needs frequent cleaning. Use it after bulk removal.

Is a centrifugal filter better than a filter press?

Neither is better in general. The centrifuge suits continuous duty and spun-dry solids. The press suits heavy solids and firm cakes at lower running speed. Choose by testing your liquid.

Talk to GTI about your project

Choosing filtration for an oil, juice or extract line? Contact Genex Tech Industries LLP (GTI Group) to discuss your material, production capacity, product specifications and utility requirements. To help us respond usefully, please share your product or raw material, required capacity, feed and final moisture (state wet or dry basis), finished-product specification, available utilities, installation location and project timeline.

Email: mktg@foodtechprojects.com
Call or WhatsApp: +91-93300-77417 | +91-87774-75596 (WhatsApp)
Website: https://foodtechprojects.com/
For Industrial Dryers: https://gtidryers.com

This article gives general technical guidance. Figures marked as illustrative are examples, not plant guarantees. Equipment selection and performance for your material should be confirmed through trials and engineering assessment.

References

  1. Codex Alimentarius, Standard for Named Vegetable Oils (CXS 210-1999). FAO/WHO. www.fao.org