Last updated: 22 November 2026. By the GTI Group editorial team, Genex Tech Industries LLP (Food Tech Projects), Kolkata, India.
Direct answer: Commercial ghee is made by concentrating milk fat as cream or butter, heating it in a ghee boiler to about 110–120 °C to drive off moisture and develop flavour, and then separating the browned residue by settling, filtration or centrifugal clarification. FSSAI limits ghee moisture to 0.5%. The creamery butter and direct cream methods suit commercial plants best.
Key takeaways
- Ghee making has three operations: fat concentration, heat clarification and residue removal.
- The direct cream method gives longer shelf life; pre-stratification of melted butter saves fuel.
- Clarification temperature drives flavour and keeping quality, so it must be controlled and recorded.
- Moisture, free fatty acids and purity tests decide whether a batch passes.

What are the commercial methods of making ghee?
There are four recognised methods: the indigenous (makkhan) method, the direct cream method, the creamery butter method (with or without pre-stratification) and continuous methods. Dairy technology teaching material notes that the creamery butter and direct cream methods are more suitable for commercial operations because less fat is lost.
| Method | Starting material | Main features | Practical notes |
|---|---|---|---|
| Indigenous (makkhan) | Hand-churned butter from curd | Heated to about 110–120 °C with stirring | Traditional flavour; labour-intensive; hard to scale |
| Direct cream | Cream | Cream heated in a ghee boiler to about 110–120 °C | Longer shelf life than creamery butter ghee; medium-fat cream gives more residue and uses more fuel |
| Creamery butter | Unsalted white butter | Butter melted, pumped to ghee boiler, clarified at about 110–120 °C | Common in organised dairies |
| Creamery butter with pre-stratification | Unsalted white butter | Melted butter held quiescent at about 80 °C; serum layer drained before boiling | Removes much of the water before boiling, saving fuel; lower acidity ghee |
| Continuous | Butter or high-fat cream | Continuous heating, evaporation and separation equipment | Suits large, steady throughput |
In the direct cream method, using high-fat cream (about 60–75% fat) instead of medium-fat cream reduces ghee residue and fuel use. Washing cream with warm water lowers non-fat solids and improves fat recovery.
What happens during heat clarification?
Clarification boils off water, denatures and browns the milk solids-not-fat, and develops the characteristic ghee flavour. The end point is judged by temperature, the stop of moisture bubbling and the colour of the residue.
When butter or cream is first heated, it froths strongly. Frothing must be controlled to avoid boil-over losses. As moisture leaves, the froth subsides and the curd particles caramelise to a golden-yellow or brown colour. Heating stops at that point. Teaching material records that clarification temperatures in parts of southern India are kept higher, about 120–140 °C, for a more pronounced flavour.
How is ghee residue removed?
After clarification, the browned residue is allowed to settle and the clear fat is separated. Plants use decantation, cloth or pressure filtration, or centrifugal clarification, depending on scale.
- Settling: hold briefly so heavy residue drops.
- Decanting or pumping: draw clear ghee from above the residue.
- Filtration or centrifugal clarification: remove fine residue for a clear, sediment-free product.
- Cooling: teaching material describes cooling to about 40–42 °C before packing in the direct cream method.
- Packing and granulation: consistent cooling and holding conditions help give the texture buyers expect.
The residue still holds fat. Many plants recover part of it by pressing or filtration, which directly improves yield.
What quality standards must ghee meet in India?
Ghee must be pure clarified milk fat. The Food Safety and Standards Authority of India (FSSAI) standard sets a maximum moisture of 0.5% and a minimum milk fat of 99.5%, along with limits for free fatty acids, Butyro-refractometer (BR) reading and Reichert-Meissl (RM) value. The Baudouin test, which detects vegetable fat, must be negative. The December 2021 FSSAI amendment also lists a Reichert-Meissl value of 24.0 for ghee.
| Parameter | Why it is tested |
|---|---|
| Moisture | Excess water shortens shelf life; FSSAI maximum 0.5%. Agmark grading uses a tighter 0.3% |
| Free fatty acids | Indicates hydrolysis and cream or butter quality; Agmark grades by FFA |
| BR reading, RM value, Polenske value | Characterise genuine milk fat and help detect adulteration |
| Baudouin test | Must be negative; detects hydrogenated vegetable fat |
| Flavour, colour, texture | Buyers expect clean flavour, uniform colour and granular texture |
Check the current FSSAI regulation for the exact values that apply to your region and milk type, because limits are revised from time to time.
What drives ghee yield and shelf life?
Yield depends mainly on the fat content of the cream or butter and on fat lost in the residue. Shelf life depends on cream ripening, method, clarification temperature, packaging and storage. Ghee typically keeps for 6–8 months at ambient temperature, limited mostly by oxidised flavour.
- Raw material: fresh, low-acidity cream or butter gives lower FFA ghee.
- Fat concentration: higher-fat feed means less water to boil off and less residue.
- Clarification control: under-heating leaves moisture; over-heating gives burnt notes.
- Packaging: low oxygen and moisture permeability slows oxidation.
- Milk type: buffalo ghee was reported to be less oxidatively stable than cow ghee because of lower natural antioxidants.
How do you estimate ghee yield from butter?
Estimate the fat going in, subtract fat lost in residue and handling, and the remainder is roughly the ghee out. The example below is illustrative; use your own fat tests and measured residue losses.
| Item (illustrative) | Value |
|---|---|
| White butter to boiler | 1,000 kg |
| Fat content of butter (assumed) | 80% |
| Fat in feed | 800 kg |
| Assumed fat lost in residue and handling | 2% of fat (16 kg) |
| Approximate ghee out (at 99.5%+ fat) | About 784 kg |
| Water and non-fat solids removed | About 200 kg as vapour and residue |
Every 1% of fat lost in this example is about 8 kg of ghee per tonne of butter. That is why residue pressing and good settling pay back quickly.
What equipment does a commercial ghee plant need?
A typical line includes cream or butter handling, a butter melter, a steam-jacketed ghee boiler with stirrer, a pre-stratification tank if used, a residue separation system (filter or clarifier), a cooling and granulation tank, and filling and packing.
GTI’s dairy processing machinery page lists a ghee making plant among its product-line systems, alongside butter churners, cream separation and pasteurisation. Share your daily cream or butter volume, fat content, preferred method and packaging so the line can be sized correctly.
Ghee lines share principles with other dairy fat lines. Hygienic design, CIP and accurate temperature recording matter throughout. GTI’s dairy page also covers pasteurisers, homogenisers, cream processing lines and CIP systems. For liquid handling, tanks and heat treatment, see GTI’s liquid food processing machinery.
Frequently asked questions
What temperature is ghee clarified at?
Commonly about 110–120 °C in the direct cream and creamery butter methods. Some regions use about 120–140 °C for a stronger flavour. The exact end point is set by moisture removal and residue colour.
Which method gives the best ghee?
For commercial production, the direct cream and creamery butter methods are preferred because fat losses are lower. The direct cream method gives longer shelf life; pre-stratification saves fuel and lowers acidity.
Why does my ghee have high moisture?
Usually because heating stopped too early or the boiler was overloaded. Check end-point temperature, batch size and stirring, and test every batch against the 0.5% FSSAI limit.
Why does ghee lose granular texture?
Texture depends on how the ghee is cooled and held after clarification. Set cooling and holding conditions by trials on your product, then keep them consistent from batch to batch.
Talk to GTI about your project
Planning a ghee plant or upgrading ghee clarification? Contact Genex Tech Industries LLP (GTI Group) to discuss your material, production capacity, product specifications and utility requirements. To help us respond usefully, please share your product or raw material, required capacity, feed and final moisture (state wet or dry basis), finished-product specification, available utilities, installation location and project timeline.
Email: mktg@foodtechprojects.com
Call or WhatsApp: +91-93300-77417 | +91-87774-75596 (WhatsApp)
Website: https://foodtechprojects.com/
For Industrial Dryers: https://gtidryers.com
This article gives general technical guidance. Figures marked as illustrative are examples, not plant guarantees. Equipment selection and performance for your material should be confirmed through trials and engineering assessment.
References
- e-PG Pathshala (INFLIBNET). Technology of ghee making: direct cream, creamery butter and continuous methods. ebooks.inflibnet.ac.in
- FSSAI. Food Safety and Standards (Food Products Standards and Food Additives) Amendment Regulations, gazette notification of 31 December 2021 (milk fat products including ghee). www.fssai.gov.in
